Home » Featured » Photoshop body paint tutorial

Photoshop body paint tutorial

Here we have a Body Painting walkthrough, that could be applied in a wide range of scenarios.Before you start, spend some time looking at examples online, here are some examples

db1

It’s All In The Highlights..

The main issue many people will face in creating this type of work, is retaining the highlights. Most paints will be moist, or reflective to a certain degree – whereas a lot of colour processing in Photoshop has a ‘dulling’ effect on reflective light. Here’s a look at the before and after for our example piece – as you can see, the soft reflected light on the right side of the body has been retained in the composite version:

db2

Compositing

To start, extract your model image onto a new layer – this will enable us to control selections, and bring in another background if required further down the line.How you deal with the extraction is up to you, however I’d sincerely urge everyone to get to grips with the Pen Tool (P), because the results can be flawless.

db3

Let’s Paint

Hold down Ctrl/Cmd and click the stock model Layer Icon, on the layer stack – this creates a selection based on the layer contents:

db4

With the selection active, create a new Gradient Map Adjustment Layer – this is handy because it will apply the effects only within the selected area.

db5

The settings used will largely depend on the tonal range of your model, plus the desired colours you would like to achieve. You can refer to the settings used in the example as a starting point, and then lead forward with your own experimentation. Listed below is the Gradient Map settings, with the RGB values of the three colour-stops used:

db6

This step will require a fair bit of ‘experimentation’ and checking the image by eye to ensure you are not flushing out the highlights. Using the Gradient Map Layer Mask, remove un-needed areas such as lips, mouth, eyes etc. using a Soft-Edged Brush (B) set to black. This Adjustment Layer was reduced to 80% opacity, to lighten the intensity a bit. Here’s a look at the example image with the first blue tone, and masked areas:

db7

Build the Tones

Although impressive, a single colour can be perceived as a little ‘flat’. Jazz up your piece by layering up more Gradient Map Adjustment Layers. To create a bit of variation for the example piece, I made another Gradient Map Adjustment Layer, and tweaked the colours using the following settings:

db8

This darker tone Adjustment Layer was set to 55% opacity, and set to Overlay layer mode. Again, areas were masked out using the Layer Mask and a Soft-Edged Brush (B) set to Black:

db9

The third tone used is another Gradient Map, this time ramping up some purple hues:

db0

There are no hard and fast rules as to what opacity or layer mode you should be using, tweak until you find the right balance – that’s all that can be said!! This final tone was set to Hard Light layer mode, with opacity of 55%:

db11

Patterns

You can enhance your body paint concept even further by creating patterns and other effects. For the example, I wanted to have some subtle alien patterning to liven it up somewhat. To achieve this, I created a new layer and created shapes with the Pen Tool (P), and filled (right-click paths, select ‘Fill’):

db12

With the basic pattern established, you can then duplicate (Ctrl/Cmd + J), and transform (Ctrl/Cmd + T) as necessary. Here you can see the pattern has been repeated and moved into place:

db13

You can use the pattern to create a selection (Ctrl/Cmd + click layer icon), and then fill or paint inside the selection. I used all kind of layer modes, opacities and techniques to create darker and lighter shades, using the pattern mask as the base. In most instances a Gaussian Blur (Filter > Blur > Gaussian Blur) was used to soften the sharp edges of the pattern, for a more natural look.

Here’s a breakdown of the pattern effects, layer by layer:

db14

Additional Textures

You can use natural media / scatter brushes for dusty texture effects, as seen in image 5, above. Simply make a new layer, and then click with your brush to get some subtle scattered textures. Ctrl/Cmd + click your original stock model layer once again (to create a selection), if you would like to keep your work within the boundaries of the stock model area.

You can find a huge selection of PS brushes within the DA Resources Gallery, if you’d like to give this step a go. One of the brushes used for the example piece:

db16

Lips & Hair

The lips and hair were worked in a similar fashion to the coloured skin tones. Again Gradient Map Adjustment Layers were used for the bulk of the work – for the lips, the layer mode was set to Hard Light, 90% Opacity. It’s a great effect, and really keeps those catch-lights in check!

db17

As my stock model is brunette, the highlights were getting a little lost; so I used the wacom to accentuate them on a new layer set to Linear Dodge:

db18

Finishing Touches..

One method that works well for pulling out the pores / skin texture is to use Unsharp Mask (Filter > Sharpen > Unsharp Mask). Create a merged copy of all your layers (Alt, Cmd/Ctrl, Shift + E) and then apply the Unsharp Mask filter with your desired settings. I really amped up the settings to increase the texture around the eyes, and selectively applied the effect using a Layer Mask.

db19

I hope you enjoyed the walkthrough!

Tags :
Uzabila

About Uzabila

Web Design, WordPress developer & enthusiast. Co-Founder of CreativeVerse.com

Leave a Reply

Your email address will not be published. Required fields are marked *

*

If you are not a robot - solve an example: * Time limit is exhausted. Please reload the CAPTCHA.

Scroll To Top